How To Clean Carburetor On Poulan Pro Chainsaw

A step-by-step chainsaw repair guide shows how to rebuild a chainsaw carburetor. The carburetor controls the air and fuel mixture that powers the engine. If the engine won't start although the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the starter rope. If the engine starts but quickly dies, the carburetor is likely the problem. Rebuild the carburetor using a manufacturer-approved rebuild kit.

Use this procedure to rebuild the carburetor on Stihl, Craftsman, MTD, Poulan, McCulloch, Troybilt and Husqvarna chainsaws. If your carburetor differs from the one shown below, check your service manual for directions specific to your model.

If you'd rather replace the carburetor, see How to Replace a Chainsaw Carburetor.

Wear work gloves to protect your hands.

In a well-ventilated area, remove the fuel cap and drain the tank into an approved storage container.

Open the fuel cap.

Remove the cylinder shield #

Using an Allen wrench, remove the screws that hold the cylinder shield to the engine. Lift off the cylinder shield.

Remove the cylinder shield

Disconnect the spark plug wire and remove the air filter #

Disconnect the wire from the spark plug. Pull the cover off the air filter housing and remove the filter.

Disconnect the spark plug wire.

Remove the air filter cover.

Remove the air filter.
Using a 7/16-inch socket driver, remove the 2 mounting nuts that secure the carburetor to the engine.

Pull the air filter housing off the carburetor.

Pull the carburetor away from the engine block. Be careful
not to bend the throttle linkage or damage the gas lines. Use needle-nose pliers to detach the gas lines from the carburetor.

Disconnect the throttle linkage. Pull the carburetor
completely off the mounting studs.

Tip: For accurate reassembly, take digital photos of the throttle linkage on the carburetor and of the gas line connections.

Remove the mounting nuts.

Remove the air filter housing.

Carefully pull the carburetor forward on the mounting studs

Pull the fuel lines off of the carburetor.

Pull the carburetor off the mounting studs.

Rebuild the carburetor #

Place the carburetor on a clean work surface and remove the screws from the bottom cover. Detach the cover.

Peel the metering diaphragm and gasket from the bottom of the carburetor. Line up the parts in order as you pull them off.

With the metering diaphragm removed, locate the lever on the hinge. Remove the mounting screw and detach the lever.

Remove the pump cover screw on the top of the carburetor.

Pull out the pump diaphragm.

Remove the screw securing the needle and fuel lever.

Remove the screw securing the needle and fuel lever.

Clean all ports and jets in the carburetor with carburetor cleaner and compressed air. Allow the carburetor to dry for at least 10 minutes.

Install the needle and lever to the bottom of the
carburetor.

Install the metering diaphragm, gasket and bottom cover.

Install the pump diaphragm and the top cover.

Tip: To speed reassembly, take digital photos of the parts before removing them.

Reinstall the carburetor #

Replace the carburetor-mounting gasket.

Connect the throttle linkage.

Slip the carburetor onto the mounting studs and push it into place.

Connect the fuel lines.

Reinstall the air filter housing.

Replace the mounting nuts and tighten them to seal the
gasket between the engine and the carburetor.

Tip: To avoid damaging the gasket by over-tightening the mounting nuts, use a torque wrench to tighten them to 25 in./lbs. If you don't have a torque wrench, tighten the nuts reasonably tight.

Install the air filter cover and connect the spark plug #

Position the air filter in the housing and replace the cover. Reattach the spark plug wire.

Reinstall the cylinder shield #

Reinstall the cylinder shield on the chainsaw. Refill the fuel tank.

Warning: Undertaking repairs to appliances can be hazardous. Use the proper tools and safety equipment noted in the guide and follow all instructions. Do not proceed until you are confident that you understand all of the steps and are capable of completing the repair. Some repairs should only be performed by a qualified technician.

If your chainsaw isn't running well, a dirty carburetor could be the problem. You can take it apart, clean it and rebuild it, using a carburetor rebuild kit.

How to replace a chainsaw carburetor

If the engine won't start even though there's fuel in the chainsaw, the carburetor could be the problem. Sometimes, it's easier to replace the carburetor than to clean it and rebuild it.

How To Replace A Chainsaw Fuel LineHow To Replace A Chainsaw Carburetor